helical rise too steep error on fadal with 88hs

Hey guys, its me again, so i just started to run a part i coded with solidCAM i3d machinig, everything was going great until i got an error and the machine stopped.

i got the HELICAL RISE TOO STEEP.

the part of the code is like this.

N11552 G01 Y-4.0484 F121.
N11554 Y-3.9451
N11556 Y-3.8648
N11558 Y-3.836
N11560 G03 X9.3109 Y-3.785 Z-0.305 I-0.0857 J0.
N11562 G01 X8.8064 Y-4.4669 F300. this feedrate was F500. but i changed it and still got the same error.
N11564 G03 X8.8693 Y-4.6033 Z-0.308 I0.0689 J-0.051 F52.
N11566 G02 X8.9024 Y-4.6075 I-0.0221 J-0.3117 F121.
N11568 G01 X8.9053 Y-4.608
N11570 G02 X8.9632 Y-4.6243 I-0.0552 J-0.3076
N11572 G01 X8.9639 Y-4.6245 F56.
N11574 X8.982 Y-4.6315 F39.
N11576 G03 X9.0215 Y-4.6426 I0.0785 J0.2042 F41.
N11578 G01 X9.024 Y-4.643
N11580 G03 X9.1044 Y-4.6448 I0.0471 J0.307
N11582 X9.1259 Y-4.6418 I-0.0193 J0.2179 F52.
N11584 G01 X9.1425 Y-4.6387 F47.
N11586 G03 X9.2518 Y-4.6027 I-0.1432 J0.6197
N11588 X9.3196 Y-4.5705 I-0.4269 J0.9848 F52.
N11590 X9.3599 Y-4.548 I-0.2853 J0.5576 F44.
N11592 X9.386 Y-4.5294 I-0.1131 J0.1872
N11594 X9.4289 Y-4.4819 I-0.1393 J0.1687 F36.
N11596 X9.4561 Y-4.424 I-0.1821 J0.1212 F49.
N11598 X9.4655 Y-4.3607 I-0.2094 J0.0633 F64.
N11600 G01 Y-4.3554 F83.
N11602 Y-4.2532
N11604 Y-4.1458 F82.
N11606 Y-4.1079 F121.
N11608 G03 X9.3155 Y-4.0513 Z-0.305 I-0.0857 J0.
N11610 G01 X8.9309 Y-4.4881 F300.
N11612 G03 X8.964 Y-4.6245 Z-0.308 I0.0643 J-0.0566 F52.
N11614 G01 X8.9672 Y-4.6258 F121.
N11616 X8.9701 Y-4.627
N11618 G02 X9.0079 Y-4.6453 I-0.1171 J-0.2897
N11620 X9.0322 Y-4.6607 I-0.1549 J-0.2714
N11622 G01 X9.0352 Y-4.6628
N11624 G02 X9.0506 Y-4.6743 I-0.1792 J-0.256 F55.
N11626 G03 X9.062 Y-4.6828 I0.1306 J0.1642 F41.
N11628 G01 X9.0692 Y-4.6877
N11630 G03 X9.0971 Y-4.704 I0.1192 J0.1727 F44.
N11632 X9.1671 Y-4.7265 I0.1329 J0.2934
N11634 X9.1853 Y-4.7296 I0.0445 J0.2051
N11636 X9.2811 Y-4.7309 I0.0532 J0.3878
N11638 X9.3142 Y-4.7241 I-0.0254 J0.2083 F52.
N11640 X9.3749 Y-4.6952 I-0.0585 J0.2015 F36.
N11642 X9.4235 Y-4.6486 I-0.1193 J0.1726 F33.
N11644 X9.4547 Y-4.589 I-0.1678 J0.126 F35.
N11646 X9.4655 Y-4.5226 I-0.1991 J0.0664 F105.
N11648 G01 Y-4.4409 F121.
N11650 Y-4.3624
N11652 G03 X9.3229 Y-4.2983 Z-0.305 I-0.0857 J0.
N11654 G01 X9.0471 Y-4.5432 F300.
N11656 G03 X9.0506 Y-4.6743 Z-0.308 I0.0569 J-0.0641 F52.
N11658 G02 X9.0769 Y-4.6978 I-0.1946 J-0.2445 F121.
N11660 G01 X9.0999 Y-4.7208 F91.
N11662 X9.1171 Y-4.7379 F61.
N11664 X9.1179 Y-4.7388 F121.
N11666 G02 X9.1355 Y-4.758 I-0.2218 J-0.2202 F80.
N11668 G01 X9.1374 Y-4.7601 F42.
N11670 X9.1536 Y-4.7769 F44.
N11672 G03 X9.1581 Y-4.7809 I0.0301 J0.0291 F41.
N11674 G01 X9.1755 Y-4.7944
N11676 X9.1797 Y-4.7973
N11678 G03 X9.2465 Y-4.8266 I0.128 J0.2015
N11680 X9.3228 Y-4.8334 I0.0605 J0.2454
N11682 G01 X9.3456 Y-4.8311
N11684 X9.3499 Y-4.8304
N11686 X9.3728 Y-4.8256
N11688 G03 X9.4402 Y-4.7988 I-0.0631 J0.2571 F52.
N11690 X9.4531 Y-4.788 I-0.0198 J0.0369 F19.
N11692 X9.4635 Y-4.7683 I-0.0491 J0.0384 F13.
N11694 X9.4655 Y-4.7554 I-0.0398 J0.0129 F94.
N11696 G01 Y-4.7369 F121.
N11698 Y-4.6428
N11700 Y-4.5432
N11702 Y-4.5242




any ideas on whats causing it?

Attached Thumbnails